Question: 11
What does a host on an Ethernet network do when it is creating a frame and it does not have the destination address?
A. Drops the frame
B. Sends out a Layer 3 broadcast message
C. Sends a message to the router requesting the address
D. Sends out an ARP request with the destination IP address
Answer: D
Cisco 100-105 Braindumps
Friday, 8 December 2017
Tuesday, 14 November 2017
Updated Cisco 100-105 Question Answers
Question: 10
Which NTP concept indicates the distance between a device and the reliable time source?
A. clock offset
B. stratum
C. reference
D. dispersion
Answer: B
Which NTP concept indicates the distance between a device and the reliable time source?
A. clock offset
B. stratum
C. reference
D. dispersion
Answer: B
Thursday, 9 November 2017
New Cisco 100-105 Question Answers
Question:9
When enabled, which feature prevents routing protocols from sending hello messages on an interface'?
A. virtual links
B. passive-interface
C. directed neighbors
D. OSPF areas
Answer: B
When enabled, which feature prevents routing protocols from sending hello messages on an interface'?
A. virtual links
B. passive-interface
C. directed neighbors
D. OSPF areas
Answer: B
Thursday, 26 October 2017
Latest Cisco 100-105 Question Answers
Question: 6
A network technician has added host A to the network. Host A cannot communicate on the network. A ping that is issued on the host to address 127.0.0.1 fails. What is the problem?
A. The router is not forwarding the ping packets to network 127.0.0.0.
B. The remote host at 127.0.0.1 is unreachable.
C. The default gateway is incorrect.
D. The IP address of host A is incorrect.
E. The TCP/IP protocols are not loaded.
Answer: E
Question: 7
A problem with network connectivity has been observed. It is suspected that the cable connected to switch port Fa0/9 on Switch1 is disconnected. What would be an effect of this cable being
disconnected?
A. Host B would not be able to access the server in VLAN9 until the cable is reconnected.
B. Communication between VLAN3 and the other VLANs would be disabled.
C. The transfer of files from Host B to the server in VLAN9 would be significantly slower.
D. For less than a minute, Host B would not be able to access the server in VLAN9. Then normal
network function would resume.
Answer: D
Question: 8
In which situation would the use of a static route be appropriate?
A. To configure a route to the first Layer 3 device on the network segment.
B. To configure a route from an ISP router into a corporate network.
C. To configure a route when the administrative distance of the current routing protocol is too low.
D. To reach a network is more than 15 hops away.
E. To provide access to the Internet for enterprise hosts.
Answer: B
A network technician has added host A to the network. Host A cannot communicate on the network. A ping that is issued on the host to address 127.0.0.1 fails. What is the problem?
A. The router is not forwarding the ping packets to network 127.0.0.0.
B. The remote host at 127.0.0.1 is unreachable.
C. The default gateway is incorrect.
D. The IP address of host A is incorrect.
E. The TCP/IP protocols are not loaded.
Answer: E
Question: 7
A problem with network connectivity has been observed. It is suspected that the cable connected to switch port Fa0/9 on Switch1 is disconnected. What would be an effect of this cable being
disconnected?
A. Host B would not be able to access the server in VLAN9 until the cable is reconnected.
B. Communication between VLAN3 and the other VLANs would be disabled.
C. The transfer of files from Host B to the server in VLAN9 would be significantly slower.
D. For less than a minute, Host B would not be able to access the server in VLAN9. Then normal
network function would resume.
Answer: D
Download Cisco Interconnecting Networking Devices 100-105 Study Material
Question: 8
In which situation would the use of a static route be appropriate?
A. To configure a route to the first Layer 3 device on the network segment.
B. To configure a route from an ISP router into a corporate network.
C. To configure a route when the administrative distance of the current routing protocol is too low.
D. To reach a network is more than 15 hops away.
E. To provide access to the Internet for enterprise hosts.
Answer: B
Friday, 13 October 2017
Cisco 100-105 Braindumps
Question: 1
Which Layer 1 devices can be used to enlarge the area covered by a single LAN segment? (Choose two.)
A. switch
B. router
C. NIC
D. hub
E. repeater
F. RJ-45 transceiver
Answer: D,E
Question: 2
What is the effect of using the service password-encryption command?
A. Only the enable password will be encrypted.
B. Only the enable secret password will be encrypted.
C. Only passwords configured after the command has been entered will be encrypted.
D. It will encrypt the secret password and remove the enable secret password from the configuration.
E. It will encrypt all current and future passwords.
Answer: E
Question: 3
What must be configured to establish a successful connection from Host A to switch SW-A through router RT-A?
A. VLAN 1 on RT-A
B. IP routing on SW-A
C. default gateway on SW-A
D. crossover cable connecting SW-A and RT-A
Answer: C
Question: 4
A switch has 48 ports and 4 VLANs. How many collision and broadcast domains exist on the
switch (collision, broadcast)?
A. 4, 48
B. 48, 4
C. 48, 1
D. 1, 48
E. 4, 1
Answer: B
Question: 5
Which method does a connected trunk port use to tag VLAN traffic?
A. IEEE 802 1w
B. IEEE 802 1D
C. IEEE 802 1Q
D. IEEE 802 1p
Answer: C
Which Layer 1 devices can be used to enlarge the area covered by a single LAN segment? (Choose two.)
A. switch
B. router
C. NIC
D. hub
E. repeater
F. RJ-45 transceiver
Answer: D,E
Question: 2
What is the effect of using the service password-encryption command?
A. Only the enable password will be encrypted.
B. Only the enable secret password will be encrypted.
C. Only passwords configured after the command has been entered will be encrypted.
D. It will encrypt the secret password and remove the enable secret password from the configuration.
E. It will encrypt all current and future passwords.
Answer: E
Question: 3
What must be configured to establish a successful connection from Host A to switch SW-A through router RT-A?
A. VLAN 1 on RT-A
B. IP routing on SW-A
C. default gateway on SW-A
D. crossover cable connecting SW-A and RT-A
Most verified Cisco 100-105 Dumps With Latest 100-105 Question Answers
Answer: C
Question: 4
A switch has 48 ports and 4 VLANs. How many collision and broadcast domains exist on the
switch (collision, broadcast)?
A. 4, 48
B. 48, 4
C. 48, 1
D. 1, 48
E. 4, 1
Answer: B
Question: 5
Which method does a connected trunk port use to tag VLAN traffic?
A. IEEE 802 1w
B. IEEE 802 1D
C. IEEE 802 1Q
D. IEEE 802 1p
Answer: C
Subscribe to:
Posts (Atom)